Leading 10 usual forklift accidents ， forklift procedure need to pay attention to these issues ！.

Do not underestimate the forklift at the workplace. If the operation is bad, there will be significant crashes in mins, and there are several mishaps involving forklifts.

Instance 1: The forklift freight obstructed the motorist's view, and the individual ahead might not be found, causing a moving mishap.
Instance 2: In order to keep the equilibrium of the forklift when lifting heavy goods, the staff members utilized their body weight as the counterweight, which virtually created casualties.
Situation 3: The size of the forklift cargo exceeds the permitted width of the path and hangs on the roadside shelf, which almost creates an accident.
Instance 4: Forklift is speeding and surrender throughout a turn.
Case 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not observe the forklift.
Instance 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not put on the seat belt, the forklift lifter drops and the motorist is squashed when the forklift rolls over.
Case 7: The forklift chauffeur did not wear a seat belt and dropped from the vehicle when it rolled over and was crushed.
Forklift operation ought to pay attention to these issues ：.

Begin.
1. Prior to beginning, observe the environments, and after verifying that there are no challenges that hinder the security of driving, beep the horn first and afterwards start.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be secure prior to starting.
3. When the forklift begins with a load, the chauffeur needs to first confirm that the load is steady and trustworthy.
4. The begin needs to be sluggish and steady.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the pole needs to be slanted in reverse. .
2. Do not lift the fork expensive when driving. When entering and leaving the task site or while driving, be careful that there will certainly be no barriers in the sky. When the tons is traveling, the fork must not be elevated too high, which will certainly influence the security of the forklift. .
3. After discharging, the fork should be reduced to the regular driving position prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal must be issued first. High-speed doglegs are prohibited. High-speed sharp turns will certainly create the car to shed lateral security and topple. .
5. When the forklift is downhill, it is purely prohibited to switch off the flame and slide, and it is prohibited to brake all of a sudden while driving with tons unless there are unique scenarios.
6. When the forklift is running, it must follow the web traffic rules in the manufacturing facility and should maintain a specific safety distance from the lorry in front. .
7. When the forklift is running, the load should remain in the most affordable setting that does not prevent the driving, and the gantry should be correctly tilted back. The tons will not be elevated except when piling or packing. .
8. The elevation of the load have to not obstruct the driver's view. In special conditions, when the thing influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving speed of the forklift in the factory area is 5 km/h, and it has to drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold items and play a stabilizing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as required to make the load of both forks balanced and not manipulated, and one side of the product ought to protest the rack. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or pull. In special conditions, security warning signs need to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging things, the forklift should be stopped with the brake. .
4. The speed of the lorry must be slow and consistent. Be careful not to roll the wheels Electric Forklift Truck for Warehouse on the dunnage, so as not to stretch the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork pointer ought to not touch various other goods or things. The load must be maintained with minimal back tilt of the gantry to make sure that the load does not move in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy positioning of the lots and extraction of the forks. .
6. It is prohibited to fork products at broadband and collide with difficult items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to utilize forks to raise workers to engage in high-altitude procedures to Stand-on Electric Pallet Stacker stay clear of high-altitude dropping mishaps. .
9. It is not allowed to utilize the brake inertia to slide, put, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork are in the air. Prior to leaving the forklift, you need to unload the goods or reduced the fork structure.
2. Pull the parking brake take care of to dead or depress the hand brake button.
3. The engine is shut off and the power is cut off. (Except for unique conditions, such as the motorist does not leave the automobile's view and does not go beyond 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance ought to be inspected, and gas, lubing oil and air conditioning water ought to be added.
2. Check the safety and security performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the operation of the forklift, examine whether the stress and temperature level are regular.
5. After the forklift is running, the exterior leak ought to also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the auto;.
2. When you run into somebody in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming should not be also sharp to stop the tendency of " totally free turning";.
6. Adding and down the incline needs to be sluggish and uniform, and no switching on the slope is permitted.
7. Do not drive throughout the gradient. When the gradient is greater than 10%, the vehicle must be driven backwards when going downhill;.
8. When the forklift personnel bring the goods and progress, if they encounter big or hefty products and most likely to the motorist's line of sight, they must take the turning around workout
.
The "Eight Prohibitions" ought to be followed in the operation.
1. Single fork operation is not permitted.
2. It is not enabled to raise the goods for long distance driving.
3. It is not permitted to get the goods by passing on the pallet with the fork.
4. It is not enabled to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not permitted to utilize inertia force to grab the goods.
6. It is not permitted to make use of braking force to exile round or easy-to-roll objects.
7. It is not allowed to bring people to work on the pallet or fork, and it is purely restricted to stand under the fork after the fork is elevated.
8. Do not drive side to side on inclines
.
Car park is not permitted under the following conditions.
1. Contours, slim roads, train crossings;.
2. Sections with a longitudinal slope more than 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the area with the very same size as the obstacle need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844